Showing posts with label rust. Show all posts
Showing posts with label rust. Show all posts

Saturday, January 7, 2012

RH front floorpan out, more underneath

After spending so much time removing that mystery goo from the passenger side front floor it turned out I needed to remove the entire patch panel. That's what I did today, and that piece of sheet metal will not be going back in.

BMW120107-01 BMW120107-02 BMW120107-03
BMW120107-04 BMW120107-05
BMW120107-06 BMW120107-07 BMW120107-08
BMW120107-09 BMW120107-10

As I was drilling out pop rivets I realized the seat had to come out. One 10mm bolt at the front of each rail, one on the outboard rear, two on the inboard. So many things are missing a fastener on this car I wonder if there should have been two on both sides. Note bracket on inboard bolt that goes up from underneath.

BMW120107-11 BMW120107-12 BMW120107-13
BMW120107-14 BMW120107-15
BMW120107-16 BMW120107-17 BMW120107-18

It is the nature of allure that what is hidden under a skirt is much more intriguing that what it is visible. I could say the same about this floor panel. When at last I had peeled off the patch panel the exposed surface seemed at first to be in terrible condition. After a few minutes poking around it turned out to be rather basic, if a bit rusty.

I was surprised to find so many layers of stuff underneath. A layer of rubbery plastic, reminds me of tar paper. Thin foam rubber. A thick layer (1/8 in.) of a black plastic that was poured on wet, looks like Bakelite. Under that is the original floor pan.

Have to find an efficient way to remove that coating.
posted from Bloggeroid

Friday, December 30, 2011

Floorpan not so good

My respiratory system showed no unusual effects after Wednesday's session. Today was all about finishing; removing the last of the goo and paint and the usual wash and metal prep cycle, maybe even a coat of POR-15 paint.

BMW111230-01 BMW111230-02 BMW111230-03

I tried using a scrub pad in combination with acetone, without much success. What did work well was to spread a "clean" rag flat, soak it with acetone, wait a minute then move it around just a bit, working the wet down into the goo. That plus some scraping on the thick spots and slowly it came off.

When the goo was gone I used a flap disk in the 4" grinder to remove most of the paint and some light corrosion. To finish off the last bits I switched to a wire brush in a die grinder.

BMW111230-04 BMW111230-05

I was working on a rough spot with the die grinder when the brush broke through a spot, and underneath was all rust. The only way to be sure it gets taken care of is to remove the repair panel floor pan. Good news, if it can be called that, is that it is pop riveted in. I can't wait to see what's lurking underneath.

I did finish with a POR-15 clean and prep, if only to prevent any more damage.
posted from Bloggeroid

Sunday, July 17, 2011

Spotting putty, upper grill opening flange

I went back to the NAPA paint center in Pearl City to pick up some wet/dry sandpaper and some spotting putty. Good news, one of the guys from the old Redline in Kalihi was working. Maybe things will work out after all. The bad news: out of anything near #100. The shop is much too small.

I am back to my short Saturday morning schedule. I really need to take some time off to make any progress. I think the Navy Seals were on the ground in Pakistan longer than I worked on the E9.

BMW110716-01

There is a series of small rust-through spots on the upper edge of both grill openings. More so on the LH side. I patched the LH side with fiberglass and POR Patch. This time I covered the metal with POR Patch and laid down the cloth, then stopped. Next time I'll saturate the cloth, maybe with POR paint. My goal is to avoid pulling the cloth out of position, especially pushing it through the holes.

BMW110716-02

Tried out the spotting putty on several places, worked well. Also bought a new can of primer, had the same aligator skin result. Could be incompatible with POR-15 Etching Primer. Next time I'll wipe the area with PPG thinner before spraying to see if that helps.

BMW110716-03

Spent more time on the LH lower front, just above the air dam. Almost there, finally.

posted from Bloggeroid

Sunday, July 3, 2011

Still on the nose, regret the loss of Redline

Took Friday off and spent much of it on the E9. Stopped off at what used to be Redline in Kalihi for a wedge shaped sanding block and some wet paper. The paint section looked worse than ever, and still no new Redline oil. I asked about the block and was told to try the "paint center" in Pearl City. Since I had the whole day I decided to undertake the adventure.

Turns out Redline is no more, bought out by NAPA. The paint center does have PPG paint, but the situation with my sanding block is cause for concern. I was told that since it is not a NAPA item it would be 6-8 weeks before it came in, if ever. So what used to be the only professional automotive paint store in Honolulu is now just another NAPA. What a shame. On balance, NAPA is the only store I trust with repair components for average cars, like my van -- water pumps and such. The others sell nothing but junk. For me it is factory original, or NAPA. Anything else is a waste of time. For specialized cars like my E9 and my Lotus there are reputable sources, just nowhere near Honolulu.

Just for fun I decided to locate the new store on Google Maps. Check the comments ... my feelings exactly. The exact opposite of the old Redline.

BMW110701-01 BMW110701-02 BMW110701-03
BMW110701-04
BMW110701-05 BMW110701-06 BMW110701-07

My Saturday session was longer due to no Gamelan rehearsal. Over the two days I got a lot done, but not much "visual progress." Sanding, a little more filler, another coat of primer. Tweaks everywhere. One place that is taking a lot of time is the area below the grill opening on the LH side. Trying to even out some old impact damage and deal with the acute angle at the joint with the air dam.

Exposed a new spot under the LH side light. Not rusted, just pitted, like old damage. Wire brushed, POR-15 clean and prep, filled with Technifill.

BMW110702-01 BMW110702-02 BMW110702-03

One new thing I did was to start grinding out some rusty spots in the underside of the hood and near the windshield opening. Nothing big. Looks like I'll have to weld a patch along the corner of the water gutter, just like the rear trunk opening. Gave all of the exposed areas the POR-15 clean and prep treatment.

I exchanged mail with Coupe King concerning door skins. Apparently he has steel for one side and aluminum (CSL style) for the other. Guess I'll keep looking. I'd like to add one of his air dams, but I'm sure I'd knock it off at the first parking lot.

posted from Bloggeroid

Sunday, December 5, 2010

Still not quite winter

I am writing this on Sunday because Saturday was too crazy. But I did work on the E9.

BMW101204-01 BMW101204-02

Started off sanding down the POR-15 Epoxy Putty applied last week to fill in the welded patch. Not much to say except it takes time, even with #40 paper. Tough stuff. Eventually I could see I had some low spots, so I decided to use TECHNIFILL, because I didn't need much thickness, and it sets fast.

What I finally concluded is that the hardener has, well, hardened. After a lot of kneading it still came out a thin blue liquid, when it used to look like blue toothpaste. But I could feel a big lump in the tube. And, like the last couple batches, it was slow to harden.

BMW101204-03 BMW101204-04 BMW101204-05

While waiting for the filler to set I used my CP grinder to expose the rust damage along the lower RH grill opening. One spot might need a welded patch. After that I worked on the top of the center grill opening, getting the opening equal on both sides. I discovered the the RH side needed to be built out a little more, so I mixed up what was supposed to be a hot batch of TECHNILL and put some on top of what was still not set. Hopefully next time will not begin with removing a bunch of half-dry filler.

BMW101204-06

The LH column of the center grill opening is pushed back a little. I tried bending and hammering, but the "U"-shaped cross sections makes this difficult. Rather than risk distorting or breaking this delicate piece I decided to try building it out with Epoxy Putty. After that I treated all the newly exposed areas with Marine Clean and Metal Prep.


Sunday, April 11, 2010

Patching the nose, #1

Last Sunday was Easter, and while I did work at the shop it was a shot day followed by a family dinner, so I never got around to uploading photos until today. I set up a Skype video phone session with my son in California -- my mother-in-law was incredulous that such a thing were possible. I make it happen I used my new T-Mobile MyTouch 3G phone tethered to my Fujitsu tablet PC. Very cool.

Lotus100411-01 Lotus100411-02 BMW100411-01

On my way in I stopped at Home Depot looking for rivets to repair the Europa's windshield wiper arm. No rivets (no surprise!), so I picked up some stainless steel cap screws (#6-32 x 1/4 in.) and matching aluminum nuts. Should look cool. The rivet hole was just 1/8 in. and to accommodate the screw I had to drill out both pieces to 9/64 in. I used Loctite on the nut. After that I noticed that the way I had been doing the spring was wrong -- it is supposed the hook onto a steel pin. There are holes for it in the cast mounting knuckle. Piano wire from a hobby shop would fit, the kind used on model airplanes. Stainless would be best. More shopping.

I also picked up a hardware storage box, which I have been meaning to do for years, and an aerosol system for POR-15 that is cheap enough to be a one-time use. After reading the instructions in more detail I see where it is like a spray can in that it can't shoot vertically. Even so it may prove useful.

BMW100404-01 BMW100404-02 BMW100404-03
BMW100404-04 BMW100404-05
BMW100404-06 BMW100404-07
BMW100404-08 BMW100404-09
BMW100404-10 BMW100404-11
BMW100404-13 BMW100404-14

Last week focused on the interior details of the nose, especially the LH side. I need to good plan on how to repair the damage around the roundel indent, most of which is on the RH side. It looks doable, but tricky. I found more thick bondo in the area around a seam where the nose joins the fender. Can't tell if this is original or collision damage repair. One of the grill mounting tabs is almost rusted off and will need a welded-on patch.

BMW100411-02 BMW100411-03 BMW100411-04 BMW100411-05 BMW100411-06

This week I decided to work my way back to welding by working on the patch for the large hole near the front LH corner. I cut and ground the hole to be more rectangular and designed the patch with a folded lip along the rear edge. I put some curvature unto it after flanging by hammering with a thick, sold steel rod and a shot bag underneath. Finished off with the usual POR-15 Marine Clean and Metal Ready treatment. The patch will be welded next time.