Showing posts with label interior. Show all posts
Showing posts with label interior. Show all posts

Friday, December 30, 2011

Floorpan not so good

My respiratory system showed no unusual effects after Wednesday's session. Today was all about finishing; removing the last of the goo and paint and the usual wash and metal prep cycle, maybe even a coat of POR-15 paint.

BMW111230-01 BMW111230-02 BMW111230-03

I tried using a scrub pad in combination with acetone, without much success. What did work well was to spread a "clean" rag flat, soak it with acetone, wait a minute then move it around just a bit, working the wet down into the goo. That plus some scraping on the thick spots and slowly it came off.

When the goo was gone I used a flap disk in the 4" grinder to remove most of the paint and some light corrosion. To finish off the last bits I switched to a wire brush in a die grinder.

BMW111230-04 BMW111230-05

I was working on a rough spot with the die grinder when the brush broke through a spot, and underneath was all rust. The only way to be sure it gets taken care of is to remove the repair panel floor pan. Good news, if it can be called that, is that it is pop riveted in. I can't wait to see what's lurking underneath.

I did finish with a POR-15 clean and prep, if only to prevent any more damage.
posted from Bloggeroid

Wednesday, December 28, 2011

Ripping out old carpet

BMW111228-01 BMW111228-02 BMW111228-03
BMW111228-04 BMW111228-05 BMW111228-06
BMW111228-07 BMW111228-08 BMW111228-09
BMW111228-10
BMW111228-11 BMW111228-12 BMW111228-13
BMW111228-14 BMW111228-15
BMW111228-16 BMW111228-17 BMW111228-18 BMW111228-19
BMW111228-20 BMW111228-21 BMW111228-22
I will not be surprised if my asthma acts up tonight, or if my allergies go haywire. I pulled out a bunch of old carpet from the passenger's side of the E9 today. Filthy, rotten carpet. The bottom layer actually looked original, which would make it 38 years old. Dust. Mildew. Candy wrappers from my kids when they were in elementary school, which was, say, fifteen years ago.

It was not my plan to remove the carpet. I started out to work in the engine compartment, where I need to weld in a patch along the gutter by the rear RH corner. To do that I needed to check what was behind the panel. That was behind the glove box, so that had to come out. Except the glove box hinge was blocked by a pile of old carpet.

I had no idea the carpet had been glued to the floorboard. The mystery glue looks like creosote; hard, tacky, sticks to skin and hard to wash off. Softened by naphtha, better removed with acetone and a wire brush. The brush breaks off tiny balls which dry and can be vacuumed. I must have wasted an hour removing this stuff and the job is still unfinished. It has to come off for the POR-15 to stick.


The floor pan and part of the firewall have been replaced using galvanized steel, which appears to be in good shape. The edges were smoothed with some kind of filler, which has dried and shrunken considerably. That has to be re-done. Even the new floor has a few small rust holes, so it will get a layer of fiberglass as part of the POR-15 process.


I did remove the glove box. The inboard support still had the original pin and snap ring, but the outboard support was a bolt and nut. Only two lag bolts attached the hinge even though there are holes for three. Had to disconnect the light wires.



posted from Bloggeroid

Saturday, October 1, 2011

Door deconstruction

Learned a lot about E9 doors today. Some things seem really well thought out, others seem haphazard. Obviously a side effect of being hand made. I also learned that one of this car's POs was a careless mechanic, because the guy I bought it from told me he swapped out the doors from some he bought on the mainland, and I found lots of missing hardware. Why use two bolts when one will do?

BMW111001-01

I decided to start with the vent window gearbox, but that was a mistake. Need to remove the entire window frame first, as it slides down into the gearbox drive shaft.

BMW111001-02 BMW111001-03 BMW111001-05 BMW111001-06 BMW111001-07 BMW111001-08

Removing the window only required two bolts, both in the rear. Appears a third bolt in the rear lift bracket was missing. The glass is passable, but not all that good. Has a long scratch along one edge (as if a rock got jammed in the window opening), and there is a chip near the upper edge. I am not going to replace it until everything else is nice. Which may be never.

BMW111001-09 BMW111001-10 BMW111001-11 BMW111001-20

The forward window rail carries all of the weight. Along with one or two normal looking bolts that go into tapped holes, there are two unusual mounts made up from slotted studs and nuts. Remove the nuts and washers, then "tighten" the studs if necessary until they slide up through the slots.

BMW111001-13 BMW111001-14 BMW111001-15 BMW111001-16 BMW111001-17

I took a series of five pictures of to detail the rust damage along the top edge. The inner panel will need some repairs before new skins can be attached. I plan to do that before removing the old skin.

BMW111001-18 BMW111001-19

The vent window connects to the gearbox via a flat tang and slotted shaft. Looks like a bolt belongs here, but nothing present.

BMW111001-21 BMW111001-22

Two quick shots of bottom edge rust damage. May need to repair inner panel but does not appear as severe as the top edge.

BMW111001-23 BMW111001-27

Removed the outer door handle and the lock.

BMW111001-24 BMW111001-25

The rear lift rail was only attached by two thin nuts at top of door. Note thin adjustment plate between nuts and door. Bottom end appears to be missing a bolt.

BMW111001-26

Removed all of the trim retaining nuts, but unable to remove trim strip because one stud was rusted to its washers. Shot with PB Blaster.

All in all a very satisfying day. Do need to get back to the nose, it needs a little more work and a coat of paint to stave off more rust.
posted from Bloggeroid